Short answer

Acrylic, also called PMMA, is a clear thermoplastic often used for display cases, boxes, signs, and light covers. Its main advantages are optical clarity, lower weight than glass of similar thickness, good weather resistance on many outdoor grades, and easy cutting, polishing, and solvent bonding. Its main disadvantages are lower impact toughness than polycarbonate, a surface that scratches more easily than glass, sensitivity to some solvents, and a service temperature that is too low for hot enclosures.

For a retail display or a lidded box that will be handled gently, clear acrylic is usually the practical choice. For a guard that may be struck, polycarbonate is usually safer. For a surface that must resist abrasion for years, glass is still harder.

What acrylic is

Acrylic is the common name for polymethyl methacrylate (PMMA). Sheet is sold under trade names such as Plexiglas, Perspex, and Acrylite. It is an amorphous thermoplastic, so it can be heated and formed, then cooled back to a rigid shape.

Two sheet routes matter in fabrication. Cast sheet is polymerized in a mold. Extruded sheet is produced continuously from melt. Cast sheet is often preferred when optical quality, thicker sections, or chemical resistance during cementing matter. Extruded sheet is often chosen for thermoforming and for cost-sensitive parts. Those are tendencies, not guarantees. Grade, thickness, and the supplier data sheet should decide the order.

Published visible-light transmission for clear optical sheet is often about 92 percent. That figure depends on grade, thickness, surface condition, and the test method. It should not be treated as a property of every acrylic part.

Advantages of acrylic

Clarity and appearance

Clear acrylic stays transparent after edge polishing, so a five-sided display case can look almost frameless. It also takes tinted, frosted, opaque, and fluorescent colors well. That is useful when a box has to match a brand color without a printed film.

Weight

Acrylic sheet is commonly around 1.18 g/cm3, roughly half the density of ordinary soda-lime glass. A counter case or a shoe box is easier to ship and to lift than the same outline in glass. Edges still need protection in transit because a sharp impact can crack a corner.

Fabrication

Acrylic can be laser-cut, CNC-routed, sawn, diamond-polished, line-bent, and joined with solvent cement. Those processes suit low-volume custom boxes better than glass, which needs different cutting and joining methods. Logos can be UV-printed or engraved. Cemented joints are strong when the joint is designed and cured correctly, but they remain a potential leak or crack path if the part is stressed.

Weathering

Many cast acrylic grades keep clarity outdoors better than uncoated polycarbonate, which can yellow unless it has a UV cap layer. Outdoor signs and covers are a common acrylic use for that reason. Indoor retail cases do not need that property, but it is relevant for window displays and exterior donation boxes.

Surface hardness relative to other clear plastics

Bare acrylic is harder than bare polycarbonate, so light wiping marks a polycarbonate guard sooner than an acrylic case. Acrylic is still softer than glass. A hard coat can improve scratch resistance, at extra cost, and it can limit later polishing.

Disadvantages of acrylic

Brittle failure

Standard acrylic cracks rather than bends when impact energy is high. It is tougher than ordinary glass in many sheet comparisons, but far less tough than polycarbonate. A floor-standing case in a busy aisle, a machine guard, or a lid that is dropped onto a hard floor is a poor fit for unmodified acrylic. Impact-modified grades exist. They usually trade away some clarity or stiffness.

Scratching

Dry paper towels, grit on a cloth, and stacked sheets without interleaving will mark the face. Fine scratches can often be polished out on uncoated sheet. Deep scratches and printed faces cannot. For a makeup organizer or a sneaker box that is opened daily, specify a cleaning method: mild soap, water, and a soft cloth. Avoid ammonia glass cleaner and alcohol unless the sheet supplier confirms the grade.

Solvents and stress crazing

Acetone, some alcohols, and strong solvents can craze or soften acrylic, especially near a cemented joint or a stressed bend. Perfume, nail-product solvents, and aggressive disinfectants are the usual retail risks. A cosmetic box should be checked against the actual product, not only against water.

Heat

Continuous-use temperature for general-purpose PMMA is often listed in supplier sheets in a band around 70-90 C, and it varies by grade. Acrylic is a poor choice next to halogen lamps, heater outlets, or dishwasher cycles. LED lighting inside a closed case is usually acceptable if the driver and strip are not trapped against the sheet and the enclosure can vent.

Static and dust

Acrylic holds a static charge, so dust shows on a clear lid. An antistatic grade or a wipe-down before packing reduces this. It does not remove the need for a sleeve or tissue between stacked parts.

Expansion and thickness limits

Acrylic expands more with temperature than glass or metal. A lid that is a tight fit at 20 C can bind in a warm shop, or rattle in a cold warehouse, if clearance was copied from a glass design. Large unsupported spans also sag. Thickness has to rise with span and with the weight of the product inside. There is no single thickness that is correct for every box.

Acrylic, glass, and polycarbonate

The table below is a selection guide, not a test report. Values such as light transmission and impact ranking change with grade, thickness, coating, and method. Confirm them on the sheet data sheet before you publish them on a product page.

Point of comparison Acrylic (PMMA) Ordinary glass Polycarbonate
Typical reason to choose it Clear display, color, easy custom fabrication Hard surface, heat, long-term abrasion Impact, vandal resistance, formed guards
Optical clarity High on clear sheet; often specified near 92% transmission High; green edge tint is common in thicker float glass High, usually a little lower than optical acrylic
Impact behavior Better than glass in many sheet uses; still brittle Breaks into sharp fragments unless tempered or laminated Much tougher; tends to dent or whiten before it shatters
Scratch resistance Better than bare polycarbonate; worse than glass Best of the three Lowest unless hard-coated
Outdoor UV Many cast grades weather well Stable, but coatings and seals still age Needs a UV-resistant grade or cap layer
Weight About half the density of glass Heaviest Similar to acrylic
Custom boxes Cut, polish, bend, and cement readily Possible, but joining and edge work cost more Possible; solvent cementing is less straightforward

When acrylic is a reasonable choice

Use acrylic when the job is presentation first and abuse second. A counter display case, a collectible cover, a ballot or suggestion box with a lock, a makeup organizer, and a lidded shoe box all fit that pattern. Visibility, color, and a polished edge matter more than surviving a hammer blow.

Move away from standard acrylic when the part is a safety guard, a hockey-rink shield, a window people may kick, or a lid that will be slammed. Polycarbonate, or acrylic with a different thickness and mounting design, should be reviewed before the drawing is frozen. Also avoid acrylic for continuous heat, strong solvent contact, and food-contact claims unless the grade and the regulations for that market are documented.

A practical rule: if the user will look through the part and wipe it occasionally, acrylic is usually enough. If the user will strike it, stack it unprotected, or clean it with solvent every day, specify a different material or a coating and write that into the order.

Practical specification notes

These ranges are shop practice for custom boxes, not material ratings.

  • Small lidded boxes often use 3 mm sheet. Larger display cases often move to 4 mm or 5 mm so the side panel does not oil-can.
  • Polished edges show scratches and cement blush more than sawn edges. Ask for a polish level, not only “clear.”
  • Leave clearance for lids and dividers. A nominal inside size with zero gap will bind after cement shrinkage and normal temperature change.
  • State whether the sheet should be cast or extruded if the part will be cemented or formed.
  • For LED cases, keep the light source off the acrylic and allow a path for heat. Acrylic diffuses light well, but it is not a heat sink.

Who SK Boxes is

The material notes above apply to acrylic in general. They are not a claim about one factory.

SK Boxes is a custom acrylic box and display-case manufacturer in Dongguan, Guangdong, China. The company has focused on acrylic fabrication since 2012. Work is wholesale and made to order: dimensions, thickness, color, compartments, printing, and packaging are set per project. Product groups include acrylic display cases, LED acrylic display cabinets, makeup organizers, and storage containers. Ordering steps are described on the how to order page. Company background is on the about us page.

A buyer still has to match grade and thickness to the use. Factory capability does not remove the scratch, impact, and solvent limits described earlier.

FAQ

Is acrylic the same as plexiglass?

Plexiglass, Perspex, and Acrylite are trade names for acrylic sheet. The polymer is PMMA. Sheet from different producers is not identical. Cast and extruded products, UV grades, and impact-modified grades should be named on the order.

Is acrylic stronger than glass?

In many impact comparisons, acrylic sheet survives blows that break ordinary glass, and it does not form the same sharp shards. It is still a brittle plastic. Polycarbonate is the usual upgrade when impact is the main risk. “Stronger” without a test method and thickness is not a useful specification.

Does acrylic yellow in sunlight?

Standard cast acrylic is widely used outdoors because many grades resist yellowing better than unstabilized polycarbonate. Pigments, coatings, and recycled content can change that result. Ask for the weathering note on the sheet grade if the part sits in a window or outside.

Can scratches be removed?

Light scratches on uncoated sheet can often be polished. Hard-coated sheet and printed graphics usually cannot. Prevention, with interleaving and a soft cloth, costs less than refinishing a finished box.

What thickness should a display box use?

There is no universal thickness. A small lid may be stable at 3 mm. A wide side panel or a heavy product often needs 4 mm, 5 mm, or a rib. Span, load, and how the case is lifted should be on the drawing before thickness is locked.

Sources

Figures in this article are described as typical published sheet data, not as test results for a single part. Primary references:

Wendy Song
Marketing Manager at SK Boxes in Dongguan since 2012, 1,000+ custom acrylic projects shipped across 50+ countries.